Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Number of Functions |
4 |
Terminal Pitch |
1.27mm |
Reach Compliance Code |
unknown |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
512/+-15V |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Power Dissipation |
640mW |
Max Supply Current |
1μA |
Turn On Delay Time |
250 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
5V~36V ±5V~20V |
Supply Type |
Dual, Single |
Turn-Off Delay Time |
140 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
20V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
250ns, 140ns |
Charge Injection |
-1pC |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
DG444DY-T1 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Extended operating temperature around -40°C~85°C TA. Totally, there are 16 terminations. This electrical component is included in the 16 series of products. These analog multiplexers are built based on SPST - NC switching circuits. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 13V. When the digital multiplexer is charged above 1μA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. If you are using a dual power supply, you should attach at least 7V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. It is possible to operate 4 inputs.
DG444DY-T1 Features
Switch Circuit: SPST - NC
DG444DY-T1 Applications
There are a lot of Vishay Siliconix DG444DY-T1 Analog Switches & Multiplexers ICs applications.
- Avionics
- Audio and video routing
- Fiber to the Home
- Sample hold systems
- Precision instrumentation
- SONET
- Multiplexers
- Precision test equipment
- Audio/video switches
- Communications systems