DG444DY-T1-E3

250ns, 140ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG444 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG444DY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 547
Description: 250ns, 140ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG444 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2014
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG444
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	36V
Power Supplies	512/+-15V
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	5μA
Nominal Supply Current	1μA
Power Dissipation	640mW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	250 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	5V~36V ±5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	140 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	20V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	250ns, 140ns
Charge Injection	-1pC
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	50Ohm
Normal Position	NC
Height	1.55mm
Length	10mm
Width	4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG444DY-T1-E3 Overview

The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 16. A electrical component with 1 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. The electrical component body receives 16 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. Search with DG444 if you are looking for analog multiplexer variants. This digital multiplexer has 160Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. An effective Dual, Single supply digital multiplexer. A low voltage of 13V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 5μA current. Put voltage above 1μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. A voltage of 36V can be used to operate the electronic component. Among the inputs that can be operated are the 4 inputs. There is 50Ohm resistance between Drain and Source for this electronic part.