DG445BDJ
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 5.08mm |
| Length | 20.13mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
DG445BDJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. This electronic part can be found in the 16 series. Multiplexers built on a SPST - NO switching circuit are built. Circuits number 4 make up this analogue multiplexer. In this multiplexer, the internal resistance is 80Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The digital multiplexer has a low cost Dual, Single supply. 13V is the lowest voltage that should be fed to the electronic electronic part. Put voltage above 1μA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG445BDJ Features
1 Channels
Switch Circuit: SPST - NO
DG445BDJ Applications
There are a lot of Vishay Siliconix DG445BDJ Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Digital cross connects (DSX-1)
- Industrial control systems
- Isolation
- Digital access cross connects
- MP3 players
- Video switching
- PDAs
- Medical Instrumentation
- Cross Connects
