Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
DG445 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
5μA |
Power Dissipation |
470mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
300ns, 200ns |
Charge Injection |
1pC |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height Seated (Max) |
5.08mm |
Length |
20.13mm |
Width |
7.62mm |
RoHS Status |
ROHS3 Compliant |
DG445BDJ-E3 Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Through Hole is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 16 pins. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for DG445 variants of the analog switch ic. The internal resistance of this digital multiplexer is 160Ohm. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. 13V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 5μA. A digital multiplexer may suffer damage if voltage is applied above 1μA. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Among the inputs that can be operated are the 4 inputs.
DG445BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG445BDJ-E3 Applications
There are a lot of Vishay Siliconix DG445BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Medical systems
- Communication systems
- Imaging
- Communications systems
- RGB switches
- Precision instrumentation
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DVD-R
- Data Acquisition Systems