DG445BDY-E3
| Parameters | |
|---|---|
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG445 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
DG445BDY-E3 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. If you are looking for variants of the digital switch, trying search with DG445. Internally, this switch multiplexer has a resistance of 160Ohm. Please refer to the datasheets for 16 pins functions. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 5μA current. Putting voltage greater than 1μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. A dual power supply should have at least 7V voltage attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating the 4 inputs requires 4 inputs.
DG445BDY-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG445BDY-E3 Applications
There are a lot of Vishay Siliconix DG445BDY-E3 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Multiplexers
- Industrial
- Precision instrumentation
- FTTH
- Audio/video switches
- Imaging
- Relay replacements
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Sample hold systems
