DG445BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | DPDT |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG445BDY-T1 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. A SPST - NO switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. A 80Ohm internal resistance characterizes this multiplexer. The functions of 16 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. 13V is the lowest voltage the electrical component should receive. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. An analog IC with the number DPDT is integrated into this board. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
DG445BDY-T1 Features
Switch Circuit: SPST - NO
DG445BDY-T1 Applications
There are a lot of Vishay Siliconix DG445BDY-T1 Analog Switches & Multiplexers ICs applications.
- SONET
- PCMCIA cards
- T1/E1 Terminals
- CSU
- Sample hold systems
- Multi-Line E1 Interface Cards
- Digital access cross connects
- Transmit
- Imaging
- Channel Banks
