DG445BDY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG445 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5μA |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 200ns |
| Charge Injection | 1pC |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
DG445BDY-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Based on SPST - NO switching circuits, these analog multiplexers work. Look for analog switch ic variants by searching with DG445. The internal resistance of this digital multiplexer is 160Ohm. For functions related to 16 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 36V voltage to the switch device. An effective Dual, Single supply digital multiplexer. It is recommended to use 13V as the lowest voltage for the electrical part. An operating current of 5μA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. This analog switch ic utilizes SEPARATE OUTPUT output. In order to operate the 4 inputs, there are several steps to follow.
DG445BDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
DG445BDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG445BDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Remote wireless modules
- DSUs
- Industrial
- High speed data transmission line cards
- PDH Multiplexers
- ATM
- SONET
- Sample hold systems
- Optical Applications
