DG445DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e0 |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation-Max | 640mW |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 22V |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 20V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 50Ohm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
DG445DY Overview
Packed in SOIC, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Bulk. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. A total of 4 circuits make up this switch device. A 85Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 13V. For this multiplexer to operate, 100pA current would be sufficient. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 7V voltage attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Additional features of the electronic component include: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY. It is not recommended to operate the switches in an environment with a temperature higher than 85°C. Resistivity from Drain to Source is 50Ohm for this electronic part.
DG445DY Features
1 Channels
100pA Supply Current
Additional Features: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY
Drain-to-Source resistance: 50Ohm
DG445DY Applications
There are a lot of Intersil (Renesas Electronics America) DG445DY Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- High-Voltage
- Precision test equipment
- Fiber to the Home
- Data switching
- Video signal routing
- Cell phones
- Isolation
- Imaging
- Mechanical reed relay replacement
