DG445DY+T
| Parameters | |
|---|---|
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 10V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG445 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Polarity | Non-Inverting |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 24V |
| Min Supply Voltage | 10.8V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -10V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 170ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 170ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG445DY+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 10V voltage supply. As part of its design, the 16 series is equipped with this electronic component. The analog switch ics are built using SPST - NO switching circuits. The circuits in this analogue multiplexer number 4. Use DG445 to search for variants of the digital switches. This digital multiplexer has 160Ohm internal resistance. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 24V to a switch device. A analog switch ic that has a cost-effective Dual, Single supply type. 10.8V should be the lowest voltage fed to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VYou should attach at least 4.5V voltage if you are using dual power supply. Operating voltages of 18V are compatible with the electrical part.
DG445DY+T Features
1 Channels
Switch Circuit: SPST - NO
DG445DY+T Applications
There are a lot of Maxim Integrated DG445DY+T Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Industrial control systems
- E1 Network Equipment
- Audio signal routing
- Multi-Line E1 Interface Cards
- Fiber to the Home
- USB 1.1 signal switching circuits
- PBXs
- Routers
- Audio and video signal routing
