DG445DYZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Packaging | Bulk |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 120 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 30mA |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 210ns |
| Drain to Source Resistance | 50Ohm |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG445DYZ Overview
This electronic part is conveniently packaged in SOIC, making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Bulk is used. In total, there are 16 terminations. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 40V voltage to the switch device. An effective Dual, Single supply digital multiplexer. 5V should be the lowest voltage fed to the electronic component. An operating current of 100pA would be sufficient for this switch device. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 5V. The electronic component can function from 20V. It is possible to operate 4 inputs. Don’t miss additional features of the electronic component such as: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY. Temperatures above 85°C should not be used to operate the switches. It has a Drain to Source resistance of 50Ohm ohms.
DG445DYZ Features
1 Channels
100pA Supply Current
Additional Features: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY
Drain-to-Source resistance: 50Ohm
DG445DYZ Applications
There are a lot of Intersil (Renesas Electronics America) DG445DYZ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- High speed data transmission line cards
- Cable Modem
- Automotive applications
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
- High-Voltage
- High reliability control systems
- Modems
- Audio and video signal routing
