DG445DYZ-T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 16 |
| Published | 1999 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 28V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 450 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 18V |
| Off-state Isolation-Nom | 60 dB |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DG445DYZ-T Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOIC. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. The internal resistance of this digital multiplexer is 160Ohm. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 40V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. 5V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 100pA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 5V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. There is a voltage range of 28V operating voltages for the electrical part. Don't forget the additional features of this electronic part, such as: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY. Temperatures above 85°C degrees Celsius should not be operated by the multiplexer. It is capable of carrying out 4-bit operation.
DG445DYZ-T Features
1 Channels
100pA Supply Current
Additional Features: IT CAN ALSO OPERATE WITH 12V SINGLE SUPPLY
4-Bit
DG445DYZ-T Applications
There are a lot of Intersil (Renesas Electronics America) DG445DYZ-T Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- RGB switches
- Multi-Line E1 Interface Cards
- Low-Voltage
- Public switching systems
- Communications systems
- Isolation
- Modems
- ISDN NT1/TA
- MP3 players
