DG445ETE+

250ns, 170ns SPST - NO 85Ohm QUAD Analog Switches DG445 16 Pins 500pA 10V 16-WQFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-DG445ETE+
Package: 16-WQFN Exposed Pad
Datasheet: PDF
Stock: 831
Description: 250ns, 170ns SPST - NO 85Ohm QUAD Analog Switches DG445 16 Pins 500pA 10V 16-WQFN Exposed Pad(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-WQFN Exposed Pad
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	1999
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	160Ohm
Terminal Finish	TIN
Technology	CMOS
Terminal Position	QUAD
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	10V
Terminal Pitch	0.8mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG445
Pin Count	16
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	30V
Min Supply Voltage	10V
Throw Configuration	SPST
Voltage - Supply, Single/Dual (±)	10V~30V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-10V
Max Dual Supply Voltage	20V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
On-state Resistance Match-Nom	4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	250ns, 170ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switch-on Time-Max	250ns
Switch-off Time-Max	170ns
Height Seated (Max)	0.8mm
Length	5mm
Width	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG445ETE+ Overview

The electronic component is convenient to ship overseas because it is packed in a 16-WQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, this analog switch is mounted. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 10V, it should be turned on and run. A total of 16 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. 4 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with DG445. As far as internal resistance is concerned, it has 160Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 10V voltage fed to the electrical part below 10V. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using dual power supplies, you should attach at least 4.5V.