Parameters |
Number of Terminations |
6 |
Resistance |
25Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
570mW |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.95mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG447 |
Output |
SEPARATE OUTPUT |
Pin Count |
6 |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
7V |
Operating Supply Current |
16μA |
Nominal Supply Current |
16A |
Power Dissipation |
570mW |
Max Supply Current |
30μA |
Throw Configuration |
SPST |
Turn On Delay Time |
130 ns |
Number of Inputs |
1 |
Voltage - Supply, Single/Dual (±) |
7V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
95 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
25Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
19pF 8pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
130ns, 95ns |
Charge Injection |
10pC |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
17Ohm |
Normal Position |
NC |
Height |
1mm |
Length |
3.05mm |
Width |
1.65mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 Thin, TSOT-23-6 |
Number of Pins |
6 |
Weight |
19.986414mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2014 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
DG447DV-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6 Thin, TSOT-23-6. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 6. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. The electrical component body receives 6 pins. A SPST - NC switching circuit is used for these analog switches. Search with DG447 if you are looking for analog multiplexer variants. Analog switches have 25Ohm internal resistance. Datasheets for 6 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 7V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 16μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 30μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VThe voltage should be at least 4.5V if you are using dual power supplies. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. In order to operate the 1 inputs, there are several steps to follow. There is 17Ohm resistance between the Drain and Source on this part.
DG447DV-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
16μA Supply Current
Drain-to-Source resistance: 17Ohm
DG447DV-T1-E3 Applications
There are a lot of Vishay Siliconix DG447DV-T1-E3 Analog Switches & Multiplexers ICs applications.
- SONET
- High-Voltage
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical
- Cell phones
- Automatic test equipment
- Isolation
- Microwave transmission systems
- Remote wireless modules
- Low-Voltage