DG451EQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Resistance | 5.3Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG451 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 5μA |
| Power Dissipation | 450mW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.13Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 256ns |
| Switch-off Time-Max | 113ns |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG451EQ-T1-E3 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. There is an electrical component included in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Circuits number 4 make up this analogue multiplexer. Use DG451 to search for variants of the digital switches. In this multiplexer, the internal resistance is 5.3Ohm. Please refer to the datasheets for 16 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. An effective Dual, Single supply digital multiplexer. A low voltage of 12V should be applied to the electronic component. The analogue multiplexer could operate on 5μA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 500nA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. A dual power supply should have at least 5V voltage attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating 4 inputs is required. Additional features of the electronic component include: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. Resistivity from Drain to Source is 4Ohm for this electronic part.
DG451EQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG451EQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG451EQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Isolation
- Microprocessor Controlled Analog Systems
- High reliability control systems
- Audio and video signal routing
- PBXs
- Video switching
- Precision data acquisition
- Remote wireless modules
- Fiber to the Home
