DG451EY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 5.3Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG451 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 600mW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 100mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.13Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 256ns |
| Switch-off Time-Max | 113ns |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG451EY-T1-E3 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~125°C TA. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. SPST - NC switching circuits are used in these analog switch ics. Try searching with DG451 to find analog multiplexer variants. As far as internal resistance is concerned, it has 5.3Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 36V should not normally be supplied to the switches. Digital switch that provides Dual, Single power at a cost-effective price. There should be 12V voltage fed to the electrical part below 12V. The analogue multiplexer could operate on 5μA current. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. For dual power supplies, a voltage of at least 5V should be attached. The electrical component supports 4 inputs. Check out the electrical component's additional features, such as the following: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. Drain to Source resistance for this electronic component is 4Ohm.
DG451EY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
5μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG451EY-T1-E3 Applications
There are a lot of Vishay Siliconix DG451EY-T1-E3 Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber to the Home
- Cable Modem
- Battery Powered Systems
- Cross Connects
- Precision test equipment
- DSUs
- RGB switches
- Audio and video routing
