DG452EQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 7.3Ohm |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG452 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 500nA |
| Power Dissipation | 450mW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 100mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.13Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 256ns |
| Switch-off Time-Max | 113ns |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG452EQ-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Temperatures around -40°C~125°C TA are extended for operation. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. An electrical component like this is included in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. Search with DG452 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 7.3Ohm. You can find the functions of the 16 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 12V voltage fed to the electrical part below 12V. An operating current of 5μA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 500nA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. For dual power supplies, a voltage of at least 5V should be attached. Operating the 4 inputs requires 4 inputs. Additional features of the electronic component include: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. This electronic component presents a Drain to Source resistance of 4Ohm.
DG452EQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG452EQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG452EQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- PDH Multiplexers
- Transmit
- Communication systems
- Microprocessor controlled systems
- Cellular phones
- Digital cross connects (DSX-1)
- Automatic test equipment
- Medical Instrumentation
- RGB switches
