DG452EY-T1-E3
| Parameters | |
|---|---|
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 7.3Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG452 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 600mW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.13Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 256ns |
| Switch-off Time-Max | 113ns |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
DG452EY-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around -40°C~125°C TA. In total, there have been 16 terminations. A electrical component with 1 channels is capable of high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with DG452 if you're looking for variants. An switch multiplexer with 7.3Ohm internal resistance has a value of 7.3Ohm. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 12V as the lowest voltage for the electrical part. An operating current of 5μA would be sufficient for this switch device. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It is possible to operate 4 inputs. This electrical component also includes additional features such as ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. A Drain to Source resistance of 4Ohm is shown for this electronic part.
DG452EY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
5μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG452EY-T1-E3 Applications
There are a lot of Vishay Siliconix DG452EY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Wireless Local Loop
- MP3 players
- Intelligent PBX
- Industrial control systems
- Battery-powered systems
- Power routing
- PCMCIA cards
- Residential Gateways, Home Gateway/Router
- High-Voltage
