DG454EY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Resistance | 5.3Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG454 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 100μA |
| Nominal Supply Current | 25μA |
| Power Dissipation | 600mW |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.12Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 112ns |
| Drain to Source Resistance | 4Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG454EY-T1-E3 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~125°C TA. The total number of terminations is 16. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. Circuits based on SPST - NC switching are used to construct these analog switch ics. Look for analog switch ic variants by searching with DG454. As far as internal resistance is concerned, it has 5.3Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. 12V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 100μA would be sufficient for this switch device. Put voltage above 100μA on the multiplexer to cause damage. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. A 4 input needs to be operated. Don’t miss additional features of the electronic component such as: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. Drain to Source resistance is 4Ohm.
DG454EY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
100μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG454EY-T1-E3 Applications
There are a lot of Vishay Siliconix DG454EY-T1-E3 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Remote Powered Equipment
- SDH
- Channelized and Unchannelized DS3 applications
- USB 1.1 signal switching circuits
- ISDN NT1/TA
- Communication systems
- Avionics
- FTTH
- SONET/SDH ADM
