DG456EQ-T1-E3

118ns, 97ns SPST - NO/NC 5.3Ohm Analog Switches BREAK-BEFORE-MAKE DG456 16 Pins 500pA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG456EQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 794
Description: 118ns, 97ns SPST - NO/NC 5.3Ohm Analog Switches BREAK-BEFORE-MAKE DG456 16 Pins 500pA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	7.3Ohm
Terminal Finish	MATTE TIN
Additional Feature	ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Subcategory	Multiplexer or Switches
Max Power Dissipation	450mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG456
Output	SEPARATE OUTPUT
Pin Count	16
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	36V
Min Supply Voltage	12V
Operating Supply Current	100μA
Power Dissipation	450mW
Max Supply Current	100μA
Throw Configuration	SPST
Turn On Delay Time	118 ns
Number of Inputs	4
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	97 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	5.3Ohm
Min Dual Supply Voltage	5V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	31pf 34pF
On-state Resistance Match-Nom	0.12Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	118ns, 97ns
Charge Injection	22pC
Channel-to-Channel Matching (ΔRon)	120m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	112ns
Voltage - Supply, Dual (V±)	±5V~15V
Height	920μm
Length	5.08mm
Width	4.4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG456EQ-T1-E3 Overview

Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. 1:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~125°C TA are extended for operation. The total number of terminations is 16. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. This electronic part can be found in the 16 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. 4 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with DG456. This digital multiplexer has 7.3Ohm internal resistance. The datasheets for the 16 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Dual, Single supply type digital switch with a low cost. A low voltage of 12V should be applied to the electronic component. This multiplexer would work with 100μA current. The analogue multiplexer may be damaged if voltage is greater than 100μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. It is recommended that you attach at least 5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. In order to operate the 4 inputs, there are several steps to follow. Additional features of the electronic component include: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY.