DG456EY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 7.3Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG456 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 12V |
| Operating Supply Current | 100μA |
| Power Dissipation | 600mW |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 118 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 5.3Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 31pf 34pF |
| On-state Resistance Match-Nom | 0.12Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 118ns, 97ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 120m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 112ns |
| Drain to Source Resistance | 4Ohm |
| Voltage - Supply, Dual (V±) | ±5V~15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG456EY-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~125°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the electrical part body. Based on SPST - NO/NC switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 4. DG456 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 7.3Ohm. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. 12V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 100μA current would be sufficient. A voltage higher than 100μA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. A dual power supply should have at least 5V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Among the inputs that can be operated are the 4 inputs. Additional features of the electronic component include: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY. Drain to Source resistance for this electronic component is 4Ohm.
DG456EY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
100μA Supply Current
Additional Features: ALSO OPERATES WITH 12V SINGLE SUPPLY AND +/-15V DUAL SUPPLY
Drain-to-Source resistance: 4Ohm
DG456EY-T1-E3 Applications
There are a lot of Vishay Siliconix DG456EY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- Video signal routing
- E1 Multiplexer
- Digital cross connects (DSX-1)
- PDAs
- Fiber to the Home
- FTTH
- Audio and video routing
- Avionics test equipment
- Medical systems
