DG458DJ-E3
| Parameters | |
|---|---|
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 1.5kOhm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| On-state Resistance Match-Nom | 90Ohm |
| Switch Time (Ton, Toff) (Max) | 250ns, 250ns |
| Channel-to-Channel Matching (ΔRon) | 90 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.5kOhm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ACTIVE OVERVOLTAGE PROTECTION |
| Max Power Dissipation | 1W |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG458 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 100μA |
| Max Supply Current | 100μA |
| Propagation Delay | 500 ns |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
DG458DJ-E3 Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 8:1. The operating temperature is extended to around -40°C~85°C TA. Totally, there are 16 terminations. This electronic part offers high-quality output due to its 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. A total of 1 circuits make up this switch device. DG458 can be used to search for analog multiplexer variants. It has an internal resistance of 1.5kOhm. Datasheets for functions of 16 pins are available. normally, users should not supply switches with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 13V. This multiplexer would work with 100μA current. When the digital multiplexer is charged above 100μA, damage can occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. With dual power supplies, you should attach at least 4.5V. This electrical part is compatible with 15V operating voltages. Check out the electrical component's additional features, such as the following: ACTIVE OVERVOLTAGE PROTECTION.
DG458DJ-E3 Features
8 Channels
100μA Supply Current
Additional Features: ACTIVE OVERVOLTAGE PROTECTION
DG458DJ-E3 Applications
There are a lot of Vishay Siliconix DG458DJ-E3 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- CSU
- T1/E1 Terminals
- Medical
- RGB switches
- Remote wireless modules
- Audio and video routing
- Cable Modem
- Residential Gateways, Home Gateway/Router
- DSLAMs
