DG4599DL-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28.009329mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG4599 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.25V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 30 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 20pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 5pC |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Switch-off Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 2.25V~5.5V |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG4599DL-T1-E3 Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 6 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. 6 pins are injected to the electronic part body. A SPDT switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG4599. It has an internal resistance of 60Ohm. Datasheets for 6 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 2.25V. For this digital switch to work, 10nA current would suffice. Draining from a single voltage supply, this analog switch requires a voltage of 2.25V~5.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. A 1 input needs to be operated. Multiplexer ics with 2 outputs are available.
DG4599DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG4599DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG4599DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Communications systems
- Remote wireless modules
- Audio/video switches
- Relay replacements
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Battery Powered Instruments
- Data Acquisition Systems
- PBX interfaces
- Transmit
- Cell phones
