Parameters |
Number of Terminations |
6 |
Resistance |
9Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
570mW |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.95mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG467 |
Pin Count |
6 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
7V |
Operating Supply Current |
20μA |
Nominal Supply Current |
5μA |
Power Dissipation |
570mW |
Max Supply Current |
15μA |
Throw Configuration |
SPST |
Turn On Delay Time |
140 ns |
Number of Inputs |
2 |
Voltage - Supply, Single/Dual (±) |
7V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
80 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
9Ohm |
Min Dual Supply Voltage |
4.5V |
High Level Output Current |
30mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
61 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
30pF 15pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
140ns, 80ns |
Charge Injection |
21pC |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
7Ohm |
Normal Position |
NC |
On-State Resistance |
7Ohm |
Height |
1.1mm |
Length |
3.05mm |
Width |
1.65mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
SOT-23-6 Thin, TSOT-23-6 |
Number of Pins |
6 |
Weight |
19.986414mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
DG467DV-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6 Thin, TSOT-23-6. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. Totally, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 6 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NC switching circuits. This multiplexer is composed of 1 circuits. Look for analog switch ic variants by searching with DG467. It has an internal resistance of 9Ohm. Datasheets for functions of 6 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Dual, Single supply type digital switch with a low cost. 7V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 20μA current. When the digital multiplexer is charged above 15μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. In order to operate the 2 inputs, there are several steps to follow. There is 7Ohm resistance between the Drain and Source on this part.
DG467DV-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
20μA Supply Current
Drain-to-Source resistance: 7Ohm
DG467DV-T1-E3 Applications
There are a lot of Vishay Siliconix DG467DV-T1-E3 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Relay replacements
- Battery Powered Instruments
- PCMCIA cards
- Audio signal routing
- FTTH
- Audio and video routing
- Sample hold systems
- PBX interfaces
- CSU