DG468DV-T1-E3

140ns, 80ns SPST - NO 9Ohm Analog Switches BREAK-BEFORE-MAKE DG468 6 Pins 1nA 15V SOT-23-6 Thin, TSOT-23-6

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG468DV-T1-E3
Package: SOT-23-6 Thin, TSOT-23-6
Datasheet: PDF
Stock: 701
Description: 140ns, 80ns SPST - NO 9Ohm Analog Switches BREAK-BEFORE-MAKE DG468 6 Pins 1nA 15V SOT-23-6 Thin, TSOT-23-6(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SOT-23-6 Thin, TSOT-23-6
Number of Pins	6
Weight	19.986414mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2017
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
Resistance	9Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	570mW
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.95mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG468
Pin Count	6
Number of Channels	2
Number of Circuits	1
Max Supply Voltage	36V
Min Supply Voltage	7V
Operating Supply Current	20μA
Nominal Supply Current	5μA
Power Dissipation	570mW
Max Supply Current	15μA
Throw Configuration	SPST
Turn On Delay Time	140 ns
Voltage - Supply, Single/Dual (±)	7V~36V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	80 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	9Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	61 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	30pF 15pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	140ns, 80ns
Charge Injection	21pC
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	7Ohm
Normal Position	NO
On-State Resistance	7Ohm
Height	1.1mm
Length	3.05mm
Width	1.65mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG468DV-T1-E3 Overview

As the electronic part is packed in SOT-23-6 Thin, TSOT-23-6, international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around -40°C~85°C TA are extended for operation. 6 terminations have been made so far. The electronic part provides high-quality output because it has 2 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 6 series of products. On the other hand, analog switches can be constructed using SPST - NO switching circuits. There are 1 circuits in this multiplexer. Try searching for the analog switch ic with DG468 if you are looking for variants. This digital multiplexer has 9Ohm internal resistance. The datasheets for the 6 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 7V. The switch device would be able to operate with 20μA current. A voltage higher than 15μA may cause damage to the switch multiplexer. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 4.5V voltage attached. There is 7Ohm resistance between Drain and Source for this electronic part.