DG470EQ-T1-E3

166ns, 108ns SPDT 6Ohm Analog Switches BREAK-BEFORE-MAKE DG470 8 Pins 500pA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG470EQ-T1-E3
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 692
Description: 166ns, 108ns SPDT 6Ohm Analog Switches BREAK-BEFORE-MAKE DG470 8 Pins 500pA 15V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Weight	139.989945mg
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	8Ohm
Terminal Finish	MATTE TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	320mW
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.65mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG470
Pin Count	8
Number of Outputs	2
Qualification Status	Not Qualified
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	12V
Operating Supply Current	3μA
Nominal Supply Current	3μA
Power Dissipation	320mW
Max Supply Current	6μA
Turn On Delay Time	166 ns
Number of Inputs	1
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	108 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	6Ohm
Min Dual Supply Voltage	4.5V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	57 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	37pF 85pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	166ns, 108ns
Charge Injection	58pC
Channel-to-Channel Matching (ΔRon)	120m Ω
Crosstalk	-63dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Dual (V±)	±4.5V~15V
Height	850μm
Length	3mm
Width	3mm
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG470EQ-T1-E3 Overview

As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad, international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 2:1. Temperatures around -40°C~125°C TA are extended for operation. 8 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. 8 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SPDT switching circuits. Look for analog switch ic variants by searching with DG470. The internal resistance of this digital multiplexer is 8Ohm. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 12V. For this multiplexer to operate, 3μA current would be sufficient. When the digital multiplexer is charged above 6μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIn the case of dual power supplies, you should connect at least 4.5V. Operating the 1 inputs requires 1 inputs. The analog switch ics includes 2 outputs.