DG508ACWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount, Through Hole |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG508A |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Operating Supply Current | 200μA |
| Throw Configuration | DPST |
| Propagation Delay | 1 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Supply Type | Dual |
| Supply Current-Max (Isup) | 0.2mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 27Ohm |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Channel-to-Channel Matching (ΔRon) | 27 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height | 2.35mm |
| Length | 10.5mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG508ACWE+ Overview
The electrical component comes in 16-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Increasing operating temperature to around 0°C~70°C TA. A total of 16 terminations have been recorded. Due to its 8 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The circuits in this analogue multiplexer number 1. Using the DG508A search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 300Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Analogue multiplexer with a Dual supply type that is cost-effective. This multiplexer would work with 200μA current. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 18V. If you are using dual power supplies, you should attach at least 4.5V. The electrical part can be operated at 15V voltage levels.
DG508ACWE+ Features
8 Channels
200μA Supply Current
DG508ACWE+ Applications
There are a lot of Maxim Integrated DG508ACWE+ Analog Switches & Multiplexers ICs applications.
- CSU
- Channelized and Unchannelized DS3 applications
- SONET
- Isolation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- USB 1.1 signal switching circuits
- Communication systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Microwave transmission systems
- Video signal routing
