DG509AAK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Operating Supply Current | 200μA |
| Power Dissipation | 800mW |
| Propagation Delay | 1 μs |
| Turn On Delay Time | 1 μs |
| Number of Inputs | 8 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 700 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 12pF |
| On-state Resistance Match-Nom | 10.2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1μs, 700ns |
| Channel-to-Channel Matching (ΔRon) | 24 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG509AAK/883B Overview
This electronic part is conveniently packaged in 16-CDIP (0.300, 7.62mm), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. In Through Hole, you'll find this switch device. There is 4:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -55°C~125°C TA degrees Celsius. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Circuits based on SP4T switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. As far as internal resistance is concerned, it has 400Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. For this digital switch to work, 200μA current would suffice. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 4.5V voltage attached. Integrated with an analog IC DIFFERENTIAL MULTIPLEXER. Operating voltages range from 15V. The 8 inputs need to be operated in order to work.
DG509AAK/883B Features
1 Channels
Switch Circuit: SP4T
200μA Supply Current
DG509AAK/883B Applications
There are a lot of Maxim Integrated DG509AAK/883B Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channel Banks
- Data Acquisition Systems
- Switching Systems
- Audio signal routing
- SDH/SONET multiplexers
- Intelligent PBX
- Precision data acquisition
- PBX interfaces
- Communication systems
