DG509ADJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 300Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG509A |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Operating Supply Current | 200μA |
| Throw Configuration | 4PST |
| Propagation Delay | 1 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 12pF |
| On-state Resistance Match-Nom | 27Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Channel-to-Channel Matching (ΔRon) | 27 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG509ADJ+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Operation at a temperature around -40°C~85°C TA. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. It is part of the design of the 16 series that this electronic component is included. A SP4T switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. Try searching for the analog switch ic with DG509A if you are looking for variants. There is 300Ohm internal resistance in this digital multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. The analog switch ic is of the Dual supply type and is cost-effective. For this multiplexer to operate, 200μA current would be sufficient. There is no problem with using dual supply voltage, but it should not exceed 18V. You should attach at least 4.5V voltage if you are using dual power supply. Operating voltages of 15V are compatible with the electrical part.
DG509ADJ+ Features
1 Channels
Switch Circuit: SP4T
200μA Supply Current
DG509ADJ+ Applications
There are a lot of Maxim Integrated DG509ADJ+ Analog Switches & Multiplexers ICs applications.
- FTTH
- USB 1.1 signal switching circuits
- E1 Multiplexer
- PCMCIA cards
- Low-Voltage
- Audio and video signal routing
- Relay replacements
- Medical
- 65 V DACs
- PBX interfaces
