Parameters |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Weight |
1.627801g |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
Published |
2012 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
500Ohm |
Max Power Dissipation |
501mW |
Technology |
CMOS |
Number of Functions |
2 |
Supply Voltage |
15V |
Base Part Number |
DG509 |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
8 |
Number of Circuits |
2 |
Max Supply Voltage |
44V |
Min Supply Voltage |
12V |
Operating Supply Current |
500μA |
Turn On Delay Time |
340 ns |
Logic Function |
Multiplexer |
Supply Type |
Dual |
Bandwidth |
250MHz |
Supply Current-Max (Isup) |
0.6mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
300 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
380Ohm |
Min Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
81 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
3pF 8pF |
On-state Resistance Match-Nom |
10Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
250ns, 240ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
10 Ω |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Voltage - Supply, Dual (V±) |
±5V~20V |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG509BEJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 4:1. Around -40°C~125°C TA is the extended operating temperature. There are 16 terminations totally. A high-quality output is provided by the electrical component's 8 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. There is an electrical component included in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. A total of 2 circuits make up this switch device. Try searching with DG509 to find analog multiplexer variants. As far as internal resistance is concerned, it has 500Ohm. To find out what the 16 pins do, please refer to the datasheets. A voltage higher than 44V should not normally be supplied to the switches. Dual supply type digital switch with a low cost. 12V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 500μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. For dual power supplies, a voltage of at least 5V should be attached. The electrical part can be operated at 15V voltage levels. It is possible to transfer data over a 250MHz-bandwidth.
DG509BEJ-E3 Features
8 Channels
Switch Circuit: SP4T
500μA Supply Current
Bandwidth: 250MHz
DG509BEJ-E3 Applications
There are a lot of Vishay Siliconix DG509BEJ-E3 Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Video signal routing
- Digital access cross connects
- PCMCIA cards
- DVD-R
- Residential Gateways, Home Gateway/Router
- Power routing
- Precision data acquisition
- ATM
- Imaging