DG509BEN-T1-GE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 380Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 12V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Element Configuration | Dual |
| Nominal Supply Current | 10μA |
| Turn On Delay Time | 340 ns |
| Bandwidth | 250MHz |
| Supply Current-Max (Isup) | 0.6mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 380Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 81 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 8pF |
| On-state Resistance Match-Nom | 10Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 250ns, 240ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Voltage - Supply, Dual (V±) | ±5V~20V |
| Height | 750μm |
| Length | 2.6mm |
| Width | 1.8mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG509BEN-T1-GE4 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-WFQFN. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 4:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. 16 terminations have been made so far. Due to its 4 channels, the electrical component produces high-quality output. A 15V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. The analog switch ics are built using SP4T switching circuits. It consists of 2 circuits. The internal resistance of this digital multiplexer is 380Ohm. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 44V. 12V is the lowest voltage that should be fed to the electronic electronic part. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. With dual power supplies, you should attach at least 5V. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. 20V operating voltages can be used with this electrical part. A 250MHz-bandwidth can be used for data transfer.
DG509BEN-T1-GE4 Features
4 Channels
Switch Circuit: SP4T
Bandwidth: 250MHz
DG509BEN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG509BEN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Cell phones
- Relay replacements
- Fiber to the Home
- Communications systems
- SONET/SDH ADM
- Audio and video routing
- Channelized and Unchannelized DS3 applications
- Microwave transmission systems
- CSU
- Microprocessor controlled systems
