banner_page

DG528CJ+

1.5μs, 1.5μs 450Ohm Analog Switches BREAK-BEFORE-MAKE DG528 18 Pins 5nA 15V 18-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-DG528CJ+
  • Package: 18-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 298
  • Description: 1.5μs, 1.5μs 450Ohm Analog Switches BREAK-BEFORE-MAKE DG528 18 Pins 5nA 15V 18-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 18-DIP (0.300, 7.62mm)
Number of Pins 18
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 1995
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 18
ECCN Code EAR99
Resistance 450Ohm
Terminal Finish Matte Tin (Sn)
Max Power Dissipation 889mW
Technology CMOS
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 15V
Terminal Pitch 2.54mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number DG528
Pin Count 18
Operating Supply Voltage 28V
Number of Channels 8
Number of Circuits 1
Max Supply Voltage 30V
Min Supply Voltage 5V
Operating Supply Current 2.5mA
Throw Configuration SP8T
Turn On Delay Time 1.5 μs
Logic Function Multiplexer
Voltage - Supply, Single/Dual (±) 5V~30V ±4.5V~20V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 1.5 μs
Max Dual Supply Voltage 20V
On-State Resistance (Max) 450Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 8:1
Off-state Isolation-Nom 68 dB
Current - Leakage (IS(off)) (Max) 5nA
Channel Capacitance (CS(off), CD(off)) 5pF 25pF
On-state Resistance Match-Nom 27Ohm
Switch Time (Ton, Toff) (Max) 1.5μs, 1.5μs
Charge Injection 4pC
Channel-to-Channel Matching (ΔRon) 27 Ω
Switching BREAK-BEFORE-MAKE
Signal Current-Max 0.02A
Height Seated (Max) 4.572mm
Length 22.86mm
Width 7.62mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Lead Free Lead Free

DG528CJ+ Overview


Shipping overseas is convenient due to the electrical component's packing in 18-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 8:1. Temperatures around 0°C~70°C TA are extended for operation. There are 18 terminations totally. The electronic part provides high-quality output because it has 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. As part of its design, the 18 series is equipped with this electronic component. 1 circuits are used in this analogue multiplexer. Using the DG528 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 450Ohm. Datasheets for functions of 18 pins are available. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 5V. It would be sufficient to run this analogue multiplexer with 2.5mA current. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIn the case of dual power supplies, you should connect at least 4.5V. It can operate from 28V operating voltages.

DG528CJ+ Features


8 Channels
2.5mA Supply Current

DG528CJ+ Applications


There are a lot of Maxim Integrated DG528CJ+ Analog Switches & Multiplexers ICs applications.

  • PBX interfaces
  • Microwave transmission systems
  • Switching Systems
  • SONET/SDH ADM
  • SDH
  • DVD-R
  • Avionics
  • Microprocessor controlled systems
  • Data Acquisition Systems
  • Mechanical reed relay replacement

Write a review

Note: HTML is not translated!
    Bad           Good