DG528CWN+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 18-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 18 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG528 |
| Pin Count | 18 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 2.5mA |
| Throw Configuration | SP8T |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1.5 μs |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 27Ohm |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1.5μs |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 27 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG528CWN+ Overview
As the electronic part is packed in 18-SOIC (0.295, 7.50mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. There are 18 terminations totally. The electronic part provides high-quality output because it has 8 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. The electrical component body receives 18 pins. There are 1 circuits in this multiplexer. Using the DG528 search parameter, you can discover variants of the switch. A 400Ohm internal resistance characterizes this multiplexer. To find out what the 18 pins do, please refer to the datasheets. Multiplexers should not be powered above 30V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. 5V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 2.5mA current. There is no problem with using dual supply voltage, but it should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. The electrical part can be operated at 28V voltage levels.
DG528CWN+ Features
8 Channels
2.5mA Supply Current
DG528CWN+ Applications
There are a lot of Maxim Integrated DG528CWN+ Analog Switches & Multiplexers ICs applications.
- PDAs
- Video switching
- SDH/SONET multiplexers
- Battery Powered Instruments
- Multiplexers
- Medical
- Avionics test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Signal routing between systems
- PBX interfaces
