DG529CWN+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 18-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 18 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG529 |
| Pin Count | 18 |
| Operating Supply Voltage | 28V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 2.5mA |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1.5 μs |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 27Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1.5μs |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 27 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1500ns |
| Switch-off Time-Max | 1500ns |
| Length | 11.55mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG529CWN+ Overview
Shipping overseas is convenient with the electronic component packed in 18-SOIC (0.295, 7.50mm Width). In order to provide high reliability, an advanced packaging method Tube is used. Mounted in Surface Mount is this multiplexer. 4:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. There are 18 terminations totally. The electronic part delivers high-quality output through its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electrical component is included in the 18 series of products. Unlike digital switches, these are based on SP4T switching circuits. Circuits number 2 make up this analogue multiplexer. Look for analog switch ic variants by searching with DG529. An switch multiplexer with 450Ohm internal resistance has a value of 450Ohm. Please refer to the datasheets for 18 pins functions. Users shouldn't supply more than 30V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. 5V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 2.5mA current. Despite this switch's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. 28V operating voltages are supported by the electronic component.
DG529CWN+ Features
4 Channels
Switch Circuit: SP4T
2.5mA Supply Current
DG529CWN+ Applications
There are a lot of Maxim Integrated DG529CWN+ Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Audio and video signal routing
- Residential Gateways, Home Gateway/Router
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Public switching systems
- Communication systems
- Signal routing between systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- HDTV
- Switching Systems
