DG604EN-T1-E4

60ns, 52ns SPST - NO 115Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG604 16 Pins 100pA 5V 16-WFQFN

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG604EN-T1-E4
Package: 16-WFQFN
Datasheet: PDF
Stock: 833
Description: 60ns, 52ns SPST - NO 115Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG604 16 Pins 100pA 5V 16-WFQFN(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mounting Type	Surface Mount
Package / Case	16-WFQFN
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tape & Reel (TR)
Published	2013
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Max Power Dissipation	525mW
Technology	CMOS
Terminal Position	QUAD
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG604
Pin Count	16
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Power Dissipation	525mW
Max Supply Current	500nA
Propagation Delay	70 ns
Turn On Delay Time	108 ns
Logic Function	Multiplexer
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	2.7V~12V ±2.7V~5V
Supply Type	Dual, Single
Bandwidth	290MHz
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	76 ns
Max Dual Supply Voltage	5V
-3db Bandwidth	400MHz
On-State Resistance (Max)	115Ohm
Min Dual Supply Voltage	2.7V
Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	2.7pF 7.3pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	60ns, 52ns
Charge Injection	0.7pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-81dB @ 10MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	90ns
Height	750μm
Length	2.6mm
Width	1.8mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG604EN-T1-E4 Overview

The electronic component is convenient to ship overseas because it is packed in a 16-WFQFN. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~125°C TA. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NO switching are used to construct these analog switch ics. A total of 2 circuits make up this switch device. Try searching with DG604 if you're looking for variants. Internally, this switch multiplexer has a resistance of 160Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexers should not be powered above 12V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.7V. In order to operate this switch device, it would need a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 500nA. There is no problem with using dual supply voltage, but it should not exceed 5V. For dual power supplies, a voltage of at least 2.7V should be attached. Among the inputs that can be operated are the 4 inputs. It is possible to transfer data over a 290MHz-bandwidth.