DG611DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 515-3V |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 5nA |
| Nominal Supply Current | 5nA |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 10V~18V ±10V~15V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Turn-Off Delay Time | 25 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 10V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 2pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 25ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -87dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 45Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG611DY Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 16. As part of its design, the 16 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NC switching circuits. The internal resistance of this digital multiplexer is 45Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 18V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 10V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 5nA current. It may damage the digital multiplexer if the voltage is higher than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 15V. A dual power supply should have at least 10V voltage attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating 4 inputs is required. The transfer of data can be performed over 500MHz bandwidths. This electronic component presents a Drain to Source resistance of 45Ohm.
DG611DY Features
Switch Circuit: SPST - NC
5nA Supply Current
Bandwidth: 500MHz
Drain-to-Source resistance: 45Ohm
DG611DY Applications
There are a lot of Vishay Siliconix DG611DY Analog Switches & Multiplexers ICs applications.
- DSUs
- Medical systems
- Industrial control systems
- Industrial
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Automotive applications
- Residential Gateways, Home Gateway/Router
- Automatic test equipment
- Modems
- SONET
