DG612DY

35ns, 25ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 250pA 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG612DY
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 925
Description: 35ns, 25ns SPST - NO 45Ohm Analog Switches BREAK-BEFORE-MAKE 16 Pins 250pA 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2009
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	45Ohm
Terminal Finish	Tin/Lead (Sn/Pb)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Terminal Form	GULL WING
Number of Functions	4
Terminal Pitch	1.27mm
Reach Compliance Code	unknown
Output	SEPARATE OUTPUT
Pin Count	16
Qualification Status	Not Qualified
Power Supplies	515-3V
Max Supply Voltage	18V
Min Supply Voltage	10V
Power Dissipation	600mW
Max Supply Current	1μA
Turn On Delay Time	50 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	10V~18V ±10V~15V
Supply Type	Dual, Single
Turn-Off Delay Time	35 ns
Max Dual Supply Voltage	15V
-3db Bandwidth	500MHz
On-State Resistance (Max)	45Ohm
Min Dual Supply Voltage	10V
Multiplexer/Demultiplexer Circuit	1:1
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	3pF 2pF
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	35ns, 25ns
Charge Injection	4pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-87dB @ 5MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	45Ohm
Normal Position	NO
Height	1.55mm
Length	10mm
Width	4mm
RoHS Status	Non-RoHS Compliant
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)

DG612DY Overview

The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. Electronic part bodies are injected with 16 pins. A SPST - NO switching circuit is used for these analog switches. The internal resistance of this digital multiplexer is 45Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 18V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 10V should be applied to the electronic component. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 15V. When using dual power supplies, you should attach at least 10V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating the 4 inputs requires 4 inputs. There is 45Ohm Drain to Source resistance on this electronic part.