DG613DY
| Parameters | |
|---|---|
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Circuits | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 5nA |
| Power Dissipation | 600mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 35 ns |
| Voltage - Supply, Single/Dual (±) | 10V~18V ±10V~15V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Turn-Off Delay Time | 25 ns |
| Max Dual Supply Voltage | 21V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | -10V |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 2pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 35ns, 25ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -87dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 45Ohm |
| Normal Position | NO/NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 45Ohm |
DG613DY Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. There is 2:2 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. Totally, there are 16 terminations. It is injected into the electrical part body with 16 pins. A DPDT switching circuit is used for these analog switches. Circuits number 1 make up this analogue multiplexer. It has an internal resistance of 45Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 18V. A analog switch ic that has a cost-effective Dual, Single supply type. 10V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 5nA current would be sufficient. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 21V. For dual power supplies, a voltage of at least -10V should be attached. Integrated with SPST analog IC. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The transfer of data can be performed over 500MHz bandwidths. There is 45Ohm Drain to Source resistance on this electronic part.
DG613DY Features
Switch Circuit: DPDT
5nA Supply Current
Bandwidth: 500MHz
Drain-to-Source resistance: 45Ohm
DG613DY Applications
There are a lot of Vishay Siliconix DG613DY Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Sample-and-hold systems
- FTTH
- Medical
- DSUs
- Audio and video routing
- PCMCIA cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical Instrumentation
- SDH/SONET multiplexers
