Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-WFQFN |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
170Ohm |
Max Power Dissipation |
525mW |
Terminal Position |
QUAD |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
DG636 |
Pin Count |
16 |
Number of Outputs |
4 |
Number of Channels |
2 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
500nA |
Power Dissipation |
525mW |
Max Supply Current |
500nA |
Turn On Delay Time |
60 ns |
Input Voltage (Max) |
5V |
Number of Inputs |
2 |
Voltage - Supply, Single/Dual (±) |
2.7V~12V ±2.7V~5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
52 ns |
Max Dual Supply Voltage |
5V |
-3db Bandwidth |
610MHz |
On-State Resistance (Max) |
115Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
2.1pF 4.2pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
60ns, 52ns |
Charge Injection |
0.1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-88dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Switch-off Time-Max |
76ns |
Signal Current-Max |
100A |
Height |
750μm |
Length |
2.6mm |
Width |
1.8mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG636EN-T1-E4 Overview
Packed in 16-WFQFN, the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. In total, there are 16 terminations. By its 2 channels, the electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. A SPDT switching circuit is used to build these analog multiplexers. Try searching with DG636 to find analog multiplexer variants. This digital multiplexer has 170Ohm internal resistance. Please refer to the datasheets for 16 pins functions. normally, users should not supply switches with voltages higher than 12V. Digital switch that provides Dual, Single power at a cost-effective price. 2.7V is the lowest voltage the electrical component should receive. An operating current of 500nA would be sufficient for this switch device. The analogue multiplexer may be damaged if voltage is greater than 500nA. If put voltage greater than 5V on the multiplexer, damage may be caused to the device. The voltage should be at least 2.7V if you are using dual power supplies. A 2 input needs to be operated. The analogue multiplexer has 4 outputs.
DG636EN-T1-E4 Features
2 Channels
Switch Circuit: SPDT
500nA Supply Current
-3db Bandwidth: 610MHz
DG636EN-T1-E4 Applications
There are a lot of Vishay Siliconix DG636EN-T1-E4 Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- E1 Multiplexer
- Isolation
- SDH/SONET multiplexers
- Voice over IP/DSL – Integrated Access Devices, Smart
- USB 1.1 signal switching circuits
- 65 V DACs
- Audio and video switching
- Precision test equipment
- Automatic test equipment