Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Weight |
140.30179mg |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2016 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
450mW |
Terminal Form |
GULL WING |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
DG636 |
Pin Count |
14 |
Number of Outputs |
4 |
Polarity |
Non-Inverting |
Number of Channels |
2 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Power Dissipation |
450mW |
Max Supply Current |
500nA |
Turn On Delay Time |
60 ns |
Input Voltage (Max) |
5V |
Number of Inputs |
2 |
Voltage - Supply, Single/Dual (±) |
2.7V~12V ±2.7V~5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
52 ns |
Max Dual Supply Voltage |
5V |
-3db Bandwidth |
610MHz |
On-State Resistance (Max) |
115Ohm |
Min Dual Supply Voltage |
2.7V |
High Level Output Current |
30mA |
Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
2.1pF 4.2pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
60ns, 52ns |
Charge Injection |
0.1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-88dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Switch-off Time-Max |
76ns |
Signal Current-Max |
100A |
Height |
900μm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG636EQ-T1-E3 Overview
Due to its 14-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~125°C TA extended. A total of 14 terminations have been recorded. A 2 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. It is part of the design of the 14 series that this electronic component is included. A SPDT switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG636. It has an internal resistance of 160Ohm. Please refer to the datasheets for 14 pins functions. normally, users should not supply switches with voltages higher than 12V. An effective Dual, Single supply digital multiplexer. It is recommended to use 2.7V as the lowest voltage for the electrical part. 1μA current would be enough for this multiplexer to operate. Put voltage above 500nA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 5V. A dual power supply should have at least 2.7V voltage attached. Among the inputs that can be operated are the 2 inputs. A analog switch ics with 4 outputs is included.
DG636EQ-T1-E3 Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 610MHz
DG636EQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG636EQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Fiber to the Home
- DSLAMs
- Sample-and-hold systems
- Routers
- Signal routing between systems
- Industrial
- Microprocessor Controlled Analog Systems
- Digital access cross connects
- Video signal routing