DG641DJ
| Parameters | |
|---|---|
| Operating Supply Voltage | 15V |
| Power Supplies | 15-3V |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 10V |
| Power Dissipation | 470mW |
| Max Supply Current | 6mA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~15V |
| Supply Type | Single |
| Bandwidth | 500MHz |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 15Ohm |
| Min Dual Supply Voltage | 10V |
| Dual Supply Voltage | 12V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 70ns, 50ns |
| Charge Injection | 19pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -87dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 15Ohm |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 15Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Terminal Position | DUAL |
| Number of Functions | 4 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
DG641DJ Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. Total terminations are 16. A total of 16 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. As far as internal resistance is concerned, it has 15Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 18V. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 10V. The analogue multiplexer may be damaged if voltage is greater than 6mA. If put voltage greater than 15V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 10V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating voltages range from 15V. The electrical component supports 4 inputs. It is possible to transfer data over a 500MHz-bandwidth. Resistivity from Drain to Source is 15Ohm for this electronic part.
DG641DJ Features
Switch Circuit: SPST - NO
Bandwidth: 500MHz
Drain-to-Source resistance: 15Ohm
DG641DJ Applications
There are a lot of Vishay Siliconix DG641DJ Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Industrial
- High reliability control systems
- Avionics test equipment
- Microwave transmission systems
- CSU
- Remote wireless modules
- 65 V DACs
- Fault Tolerant Systems
- Switching Systems
