DG642DY-E3
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 15Ohm |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 300mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG642 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 15V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 21V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 3.5mA |
| Power Dissipation | 300mW |
| Max Supply Current | 6mA |
| Turn On Delay Time | 100 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~15V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 8Ohm |
| Min Dual Supply Voltage | 10V |
| High Level Output Current | 100mA |
| Dual Supply Voltage | 12V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 60ns |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 8Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG642DY-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. 8 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 8 pins. The analog switch ics are built using SPDT switching circuits. Using the DG642 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 15Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 21V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual, Single supply. There should be 10V voltage fed to the electrical part below 10V. The analogue multiplexer could operate on 3.5mA current. A digital multiplexer may suffer damage if voltage is applied above 6mA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 15V. In the case of dual power supplies, you should connect at least 10V. It is integrated with AUDIO/VIDEO SWITCH analog ICs. The electrical part can be operated at 15V voltage levels. In order to operate the 1 inputs, there are several steps to follow. There are 500MHz bandwidths for data transfer. You shouldn't miss the additional features of the electrical component, such as: VIDEO APPLICATION. There is 8Ohm Drain to Source resistance on this electronic part. This digital multiplexer has 2 outputs.
DG642DY-E3 Features
1 Channels
Switch Circuit: SPDT
3.5mA Supply Current
Bandwidth: 500MHz
Additional Features: VIDEO APPLICATION
Drain-to-Source resistance: 8Ohm
DG642DY-E3 Applications
There are a lot of Vishay Siliconix DG642DY-E3 Analog Switches & Multiplexers ICs applications.
- Cell phones
- Cellular phones
- Data Acquisition Systems
- Microprocessor Controlled Analog Systems
- Communication systems
- SDH/SONET multiplexers
- USB 1.1 signal switching circuits
- MP3 players
- Routers
- DSLAMs
