DG642DY-T1-E3
| Parameters | |
|---|---|
| On-State Resistance (Max) | 8Ohm |
| Min Dual Supply Voltage | 10V |
| Dual Supply Voltage | 12V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 60ns |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO/NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 8Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 300mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG642 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 3.5mA |
| Power Dissipation | 300mW |
| Max Supply Current | 6mA |
| Throw Configuration | SPDT, SPST |
| Turn On Delay Time | 100 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~15V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 60 ns |
| Max Dual Supply Voltage | 15V |
DG642DY-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around -40°C~85°C TA extended. A total of 8 terminations have been recorded. A 1 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPDT switching circuits. If you are looking for variants of the digital switch, trying search with DG642. In this multiplexer, the internal resistance is 8Ohm. Datasheets for functions of 8 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 18V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. 10V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 3.5mA current. It may damage the digital multiplexer if the voltage is higher than 6mA. There is no problem with using dual supply voltage, but it should not exceed 15V. A dual power supply should have at least 10V voltage attached. This product is integrated with an analog integrated circuit (IC) of type AUDIO/VIDEO SWITCH. There is a voltage range of 15V operating voltages for the electrical part. There are 1 inputs to be operated. A 500MHz-bandwidth can be used for data transfer. Don't forget the additional features of this electronic part, such as: VIDEO APPLICATION. There are 2 outputs on the analogue multiplexer.
DG642DY-T1-E3 Features
1 Channels
Switch Circuit: SPDT
3.5mA Supply Current
Bandwidth: 500MHz
Additional Features: VIDEO APPLICATION
DG642DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG642DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- FTTH
- Cell phones
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- RGB switches
- ISDN NT1/TA
- USB 1.1 signal switching circuits
- Communication systems
- Sample-and-hold systems
- SDH
- Digital cross connects (DSX-1)
