DG643DJ
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 15Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Reach Compliance Code | unknown |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Power Supplies | 15-3V |
| Number of Circuits | 2 |
| Max Supply Voltage | 21V |
| Min Supply Voltage | 10V |
| Max Supply Current | 6mA |
| Turn On Delay Time | 70 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~15V |
| Supply Type | Single |
| Bandwidth | 500MHz |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 15Ohm |
| Min Dual Supply Voltage | 10V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 50ns |
| Charge Injection | 19pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -87dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG643DJ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature around -40°C~85°C TA extended. 16 terminations have been made so far. As part of its design, the 16 series is equipped with this electronic component. On the other hand, analog switches can be constructed using SPDT switching circuits. It consists of 2 circuits. Internally, this switch multiplexer has a resistance of 15Ohm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. A voltage higher than 21V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10V. If you put voltage higher than 6mA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 15V. If you are using a dual power supply, you should attach at least 10V. Operating voltages range from 15V. The data can be transferred over a wide range of bandwidths, called 500MHz bandwidths.
DG643DJ Features
Switch Circuit: SPDT
Bandwidth: 500MHz
DG643DJ Applications
There are a lot of Vishay Siliconix DG643DJ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Relay Replacement
- CSU
- Central office
- Audio signal routing
- Sample-and-hold systems
- Sample hold systems
- Signal routing between systems
- High reliability control systems
- Battery Powered Instruments
