DG643DY-E3
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 665.986997mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 15Ohm |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG643 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Polarity | Non-Inverting |
| Power Supplies | 15-3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 10V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 3.5mA |
| Nominal Supply Current | 3.5mA |
| Power Dissipation | 600mW |
| Max Supply Current | 6mA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~15V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 15V |
| On-State Resistance (Max) | 15Ohm |
| Min Dual Supply Voltage | 10V |
| High Level Output Current | 75mA |
| Dual Supply Voltage | 12V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 50ns |
| Charge Injection | 19pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -87dB @ 5MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 15Ohm |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG643DY-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPDT switching circuits. 2 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with DG643. There is 15Ohm internal resistance in this digital multiplexer. The functions of 8 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 18V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. There should be 10V voltage fed to the electrical part below 10V. An operating current of 3.5mA would be sufficient for this switch device. When the digital multiplexer is charged above 6mA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 15V. If you are using dual power supplies, you should attach at least 10V. There is an analog IC AUDIO/VIDEO SWITCH integrated with this board. The electronic component can function from 15V. Among the inputs that can be operated are the 4 inputs. This switch operates within the bandwidth of 500MHz. Additional features include: VIDEO APPLICATION. A Drain to Source resistance of 15Ohm is shown for this electronic part.
DG643DY-E3 Features
1 Channels
Switch Circuit: SPDT
3.5mA Supply Current
Bandwidth: 500MHz
Additional Features: VIDEO APPLICATION
Drain-to-Source resistance: 15Ohm
DG643DY-E3 Applications
There are a lot of Vishay Siliconix DG643DY-E3 Analog Switches & Multiplexers ICs applications.
- Medical
- ISDN NT1/TA
- Sample-and-hold systems
- E1 Network Equipment
- Industrial
- Multi-Line E1 Interface Cards
- Routers
- DSUs
- High speed data transmission line cards
- Remote Powered Equipment
