DG9052DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Resistance | 40Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 925mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9052 |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 925mW |
| Max Supply Current | 1μA |
| Propagation Delay | 80 ns |
| Turn On Delay Time | 90 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.7V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 30 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 40Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 79 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 8pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 35ns, 30ns |
| Charge Injection | 38pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω (Max) |
| Crosstalk | -83dB @ 1MHz |
| Switch-on Time-Max | 70ns |
| Switch-off Time-Max | 50ns |
| Height | 920μm |
| Length | 5.07mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG9052DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 4:1. Increasing operating temperature to around -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 4 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. It is injected into the electrical part body with 16 pins. Based on SP4T switching circuits, these analog multiplexers work. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with DG9052. In this multiplexer, the internal resistance is 40Ohm. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 12V. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 2.7V. The switch device would be able to operate with 1μA current. When the digital multiplexer is charged above 1μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWith dual power supplies, you should attach at least 2.7V. 3V operating voltages can be used with this electrical part. It is possible to operate 8 inputs.
DG9052DQ-T1-E3 Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
DG9052DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9052DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- SONET
- 65 V DACs
- RGB switches
- Cable Modem
- Communications systems
- Remote wireless modules
- Video signal routing
- Battery-powered systems
- Video switching
- E1 Network Equipment
