DG9053DQ-T1-E3

35ns, 30ns SPDT 40Ohm Analog Switches BREAK-BEFORE-MAKE DG9053 16 Pins 1nA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9053DQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 224
Description: 35ns, 30ns SPDT 40Ohm Analog Switches BREAK-BEFORE-MAKE DG9053 16 Pins 1nA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	500mOhm
Terminal Finish	MATTE TIN
Additional Feature	ALSO OPERATE WITH 2.7V TO 12V SINGLE SUPPLY
Max Power Dissipation	925mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	3
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG9053
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	3V
Number of Channels	1
Number of Circuits	3
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Power Dissipation	925mW
Max Supply Current	1μA
Turn On Delay Time	45 ns
Logic Function	Multiplexer
Number of Inputs	6
Voltage - Supply, Single/Dual (±)	2.7V~12V ±2.7V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	40 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	40Ohm
Min Dual Supply Voltage	2.7V
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	79 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	4pF 8pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	35ns, 30ns
Charge Injection	38pC
Channel-to-Channel Matching (ΔRon)	5 Ω (Max)
Crosstalk	-83dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	70ns
Switch-off Time-Max	50ns
Height	920μm
Length	5.08mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant

DG9053DQ-T1-E3 Overview

Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. The analog switch ics are built using SPDT switching circuits. There are 3 circuits in this switch device. Try searching for DG9053 variants of the analog switch ic. This digital multiplexer has 500mOhm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. normally, users should not supply switches with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2.7V. An operating current of 1μA would be sufficient for this switch device. It may damage the digital multiplexer if the voltage is higher than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. If you are using dual power supplies, you should attach at least 2.7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. A voltage of 3V can be used to operate the electronic component. It is possible to operate 6 inputs. Additional features include: ALSO OPERATE WITH 2.7V TO 12V SINGLE SUPPLY.