Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
Number of Pins |
8 |
Weight |
139.989945mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
30Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
400mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG9232 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5V |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
75 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
On-State Resistance (Max) |
30Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
74 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
7pF 13pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
75ns, 50ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
400m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2.7V~12V |
Drain to Source Resistance |
30Ohm |
Normal Position |
NO |
Height |
850μm |
Length |
3mm |
Width |
3mm |
RoHS Status |
ROHS3 Compliant |
DG9232DQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. There are 8 terminations totally. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. As part of its design, the 8 series is equipped with this electronic component. SPST - NC switching circuits are used in these analog switch ics. Try searching for the analog switch ic with DG9232 if you are looking for variants. As far as internal resistance is concerned, it has 30Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 2.7V. The analogue multiplexer could operate on 1μA current. Using a single voltage supply, this switch device consumes 2.7V~12V volts. Putting voltage greater than 1μA on the multiplexer may cause damage. This analog switch ic utilizes SEPARATE OUTPUT output. Operating the 2 inputs requires 2 inputs. Drain to Source resistance for this electronic component is 30Ohm.
DG9232DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
Drain-to-Source resistance: 30Ohm
DG9232DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9232DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Fiber to the Home
- Digital Cross-Connects
- Audio and video signal routing
- High speed data transmission line cards
- Routers
- E1 Multiplexer
- Automatic test equipment
- Switching Systems