DG9232DY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 30Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9232 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 13pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG9232DY-T1-E3 Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. This electrical component is included in the 8 series of products. The analog switch ics are built using SPST - NC switching circuits. Try searching for DG9232 variants of the analog switch ic. This digital multiplexer has 30Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 12V. An effective Single supply digital multiplexer. 2.7V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~12V. A digital multiplexer may suffer damage if voltage is applied above 1μA. This analog switch ic utilizes SEPARATE OUTPUT output. In order to operate the 2 inputs, there are several steps to follow.
DG9232DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG9232DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG9232DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Remote wireless modules
- Battery Powered Instruments
- Audio and video routing
- Avionics and Military Systems
- RGB switches
- Channel Banks
- Central office
- Communication systems
- E1 Network Equipment
