DG9233DQ-T1-E3

75ns, 50ns SPST - NO 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9233 8 Pins 100pA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9233DQ-T1-E3
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 469
Description: 75ns, 50ns SPST - NO 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9233 8 Pins 100pA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Inquiry Now

Details

Tags

Parameters
Normal Position	NO
Height	850μm
Length	3mm
Width	3mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Weight	139.989945mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	30Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG9233
Output	SEPARATE OUTPUT
Pin Count	8
Power Supplies	3/5V
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	75 ns
Number of Inputs	2
Supply Type	Single
Turn-Off Delay Time	50 ns
On-State Resistance (Max)	30Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	74 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	7pF 13pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	75ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.7V~12V

DG9233DQ-T1-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. There are 8 pins injected into the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. Try searching for the analog switch ic with DG9233 if you are looking for variants. It has an internal resistance of 30Ohm. To find out what the 8 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. There should be 2.7V voltage fed to the electrical part below 2.7V. An operating current of 1μA would be sufficient for this switch device. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. This analog switch ic utilizes SEPARATE OUTPUT output. It is possible to operate 2 inputs.