DG9233DY
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 13pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Drain to Source Resistance | 30Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 30Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
DG9233DY Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. In total, 8 terminations have occurred. Into the electrical component body are injected 8 pins. A SPST - NO switching circuit is used to build these analog multiplexers. A 30Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 8 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. A cost-effective Single supply type analogue multiplexer. It is recommended to use 2.7V as the lowest voltage for the electrical part. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating the 2 inputs requires 2 inputs. There is 30Ohm resistance between Drain and Source for this electronic part.
DG9233DY Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 30Ohm
DG9233DY Applications
There are a lot of Vishay Siliconix DG9233DY Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Low-Voltage
- Channel Banks
- SONET/SDH ADM
- Cable PC
- Cable Modem
- Signal routing between systems
- Industrial and process control systems
- Relay replacements
- Digital cross connects (DSX-1)
